BREW-BOSS COFI MASH INFUSION FILTER FOR 15 GALLON KETTLE

BREW-BOSS COFI MASH INFUSION FILTER FOR 15 GALLON KETTLE Center Out Forced Infusion The Brew-Boss #COFI filter is an exciting technology that optimizes the efficiency of Brew-In-A-Bag (#BIAB) type brewing. The filter is manufactured from 304 grade stainless steel mesh which holds the grain during the mash process, but allows water to flow through. The filter is 13 inches in diameter x 13.5 inches high. The support legs allow the filter to sit above the heating element and are 2-1/2 inches tall. This brings the total height of the unit to 16 inches. The 90 degree barbed elbow at the top adds another 1-1/2 inches, for a total overall height of this filter with the barbed fitting installed of 17.5 inches. Make certain your kettle is tall enough to contain this filter with the cover on. The filter can hold approximately 20 pounds of crushed grain. This amount depends on the crush and the grain. This item is provided for brewers to add to their existing (Brew-Boss or other Manufacturer) breweries and includes the following items: Mesh basket with 2.5" long feet to clear heating element. Mesh Cover with Stainless Steel Clamps and Handle Center Infusion Tube False Bottom with Threaded Infusion Tube Mount Stainless Elbow Fitting for Top of Infusion Tube Stainless Lift Ring Adapter Type C Camlock Female Fitting 12" Silicone Brewery Grade Tubing A central infusion tube, that is perforated with a series of flow-matched holes, extends all the way to the bottom of the filter. During the mash cycle, water is continuously pumped from the bottom of the kettle to the top of the filter, into the central infusion tube, where it is forced through the grain bed. Water passing through the grain bed flows out of the filter to the bottom of the kettle. This Center Out Forced Infusion (COFI) technology assures that all the grain is in constant contact with the mash water and that there are no dead spots. No stirring is required as the system is self agitating and efficiency is thereby optimized. The COFI filter is also very easy to clean, simply invert it in a sink and spray it with your sprayer! Because it is made of stainless steel, it will not rust and will last indefinitely. The central infusion tube is also connected to a false bottom. After mashing is completed, the elbow fitting at the top of the COFI filter is exchanged with a lifting ring. When removing the filter, the filter is lifted by the lift ring. This brings the false bottom towards the fixed cover, allowing the weight of the filter to squeeze the grain. This squeezing action extracts much of the trapped sweet wort from the grain. www.brew-boss.com

Brew-Boss Automated Homebrew System Brew Session: App & COFI Filter

Brew-Boss Automated Homebrew System Brew Session
Brew-Boss Brewing Session Highlights. Takes you through the entire process of brewing with the Brew-Boss electric homebrew system. The COFI mash infusion system was used for this batch.
www.brew-boss.com

#electrichomebrew, #brewboss, #makegreatbeer, #biab, #makegreatbeer

Br

Brew Boss: Beer Brewing App - Talks you through the process

Brew-Boss Automated Electric Homebrew System App walks user through brewing process with Verbal prompts. Even users that have never brewed before can make All-Grain beer successfully their very first batch.
www.brew-boss.com

#homebrewing, #brewboss, #electricbrewingrocks, #makegreatbeer, #bestbeerbrewingappever

Br

Low Price SS Heatling Elements - 5500 Watt, 2250 Watt, 1650 Watt

Low Price SS Heatling Elements - 5500 Watt, 2250 Watt, 1650 Watt

5500 Watt - Was $75, NOW $50
https://www.brew-boss.com/ULWD-L6-30P-Stainless-Steel-Ripple-Heater-Element-p/htr-5500-ripple-l6-30p.htm

Beware of cheap copies with rubber band covers over the high voltage terminals and corrosive parts. They are not safe and are poorly constructed. The Brew-Boss heater is 100% potted with epoxy and is waterproof. No worries when cleaning about getting water inside the element. It features an integrated 1.5" Tri-Clamp ferrule as well as an integrated L6-30P twist lock plug! Never has it been so easy to convert to electric brewing. No longer do you have to figure out how to enclose your heater element to make it safe. Any L6-30R twist lock receptacle will connect to this element or use the Brew-Boss Heater Cable for a perfect fit. This heater requires a 1.5" Tri-Clamp flange on your kettle (all Brew-Boss kettles have this flange welded on). If you are converting to electric or have another brand of kettle, you can add a Tri-Clamp flange by having one welded on locally or by using our Weldless 1.5 Inch Tri-Clamp Bulkhead Adapter. The element is constructed of shiny 304 stainless steel and will look like new for years. it is an ULWD (Ultra Low Watt Density) element, so no worries about scorching your wort. The element itself is 14 inches long and the ferrule is a 1.5" Tri-Clamp. Please order the clamp and gasket separately as they are not included with this item. This listing is for the heater element only. Pictures of the element with the mating Brew-Boss Heater cable are shown only to show how the components fit together. 304 Stainless Steel 14" Long Ripple Style 240 Volts AC 5500 Watts Ultra Low Watt Density Integrated L6-30P Twist Lock Plug Integrated 1.5" Tri-Clamp Flange Epoxy filled making it waterproof

2250 Watt - Was $65, NOW $40
https://www.brew-boss.com/120-Volt-2250-Watt-Foldback-Heating-Element-p/htr-2250-foldback-l6-30p.htm

It features an integrated 1.5" Tri-Clamp ferrule as well as an integrated L6-30P twist lock plug! Never has it been so easy to convert to electric brewing. No longer do you have to figure out how to enclose your heater element to make it safe. Any L6-30R twist lock receptacle will connect to this element or use the Brew-Boss Heater Cable for a perfect fit. This element requires a 20 amp 120 volt AC circuit to operate. Most residential outlets are 15 amp circuits. Make certain that you have a 20 amp circuit if you plan to use this heater. This heater requires a 1.5" Tri-Clamp flange on your kettle (all Brew-Boss kettles have this flange welded on). If you are converting to electric or have another brand of kettle, you can add a Tri-Clamp flange by having one welded on locally or by using our Weldless 1.5 Inch Tri-Clamp Bulkhead Adapter. The element is constructed of shiny 304 stainless steel and will look like new for years. it is an ULWD (Ultra Low Watt Density) element, so no worries about scorching your wort. The element itself is 9 inches long and the ferrule is a 1.5" Tri-Clamp. Please order the clamp and gasket separately as they are not included with this item. This listing is for the heater element only. 304 Stainless Steel 9" Long Foldback Style 120 Volts AC 2250 Watts Ultra Low Watt Density Integrated L6-30P Twist Lock Plug Integrated 1.5" Tri-Clamp Flange

1650 Watt -  Was $65, NOW $40

https://www.brew-boss.com/120-Volt-1650-Watt-Foldback-Heating-Element-p/htr-1650-foldback-l6-30p.htm

It features an integrated 1.5" Tri-Clamp ferrule as well as an integrated L6-30P twist lock plug! Never has it been so easy to convert to electric brewing. No longer do you have to figure out how to enclose your heater element to make it safe. Any L6-30R twist lock receptacle will connect to this element or use the Brew-Boss Heater Cable for a perfect fit. This heater requires a 1.5" Tri-Clamp flange on your kettle (all Brew-Boss kettles have this flange welded on). If you are converting to electric or have another brand of kettle, you can add a Tri-Clamp flange by having one welded on locally or by using our Weldless 1.5 Inch Tri-Clamp Bulkhead Adapter. The element is constructed of shiny 304 stainless steel and will look like new for years. it is an ULWD (Ultra Low Watt Density) element, so no worries about scorching your wort. The element itself is 9 inches long and the ferrule is a 1.5" Tri-Clamp. Please order the clamp and gasket separately as they are not included with this item. This listing is for the heater element only. 304 Stainless Steel 9" Long Foldback Style 120 Volts AC 1650 Watts Ultra Low Watt Density Integrated L6-30P Twist Lock Plug Integrated 1.5" Tri-Clamp Flange

www.brew-boss.com

#heatingelements, #brewboss, #homebrew

Video: Fill-Boss Automated Bottle and Growler filler for Beer and Wine

Brew Boss Black Friday Sale 2019!!

Brew Boss Black Friday Sale 2019!!

10 Gallon Kettle
5500 Watt 240 Volt Tri-Clover Heating Element
1650 Watt 120 Volt Tri-Clover Heating Element
2250 Watt 120 Volt Tri-Clover Heating Element

10 GALLON BREW-BOSS KETTLE KIT

10 Gallon Brew-Boss Kettle with Welded Tri-Clamp ferrules for the heaters and valve. This kettle includes three Tri-Clamp ferrules for the valve and dual heater assemblies. Also includes Cover, DELUXE Accessory Port, and Direct Contact Weldless Temperature Probe Mount.

Dia 350mm X H 420mm (13.75 in x 16.5 in) This is an optimum 1.2:1 ratio kettle!

240 VOLT 5500 WATT RIPPLE HEATING ELEMENT WITH INTEGRATED L6-30P PLUG AND TRICLAMP MOUNT

This product was designed by Brew-Boss and is manufactured exclusively for Brew-Boss!

Beware of cheap copies with rubber band covers over the high voltage terminals and corrosive parts. They are not safe and are poorly constructed. The Brew-Boss heater is 100% potted with epoxy and is waterproof. No worries when cleaning about getting water inside the element.

It features an integrated 1.5" Tri-Clamp ferrule as well as an integrated L6-30P twist lock plug! Never has it been so easy to convert to electric brewing. No longer do you have to figure out how to enclose your heater element to make it safe. Any L6-30R twist lock receptacle will connect to this element or use the Brew-Boss Heater Cable for a perfect fit.

This heater requires a 1.5" Tri-Clamp flange on your kettle (all Brew-Boss kettles have this flange welded on). If you are converting to electric or have another brand of kettle, you can add a Tri-Clamp flange by having one welded on locally or by using our Weldless 1.5 Inch Tri-Clamp Bulkhead Adapter.

The element is constructed of shiny 304 stainless steel and will look like new for years. it is an ULWD (Ultra Low Watt Density) element, so no worries about scorching your wort.

The element itself is 14 inches long and the ferrule is a 1.5" Tri-Clamp. Please order the clamp and gasket separately as they are not included with this item.

This listing is for the heater element only. Pictures of the element with the mating Brew-Boss Heater cable are shown only to show how the components fit together.

• 304 Stainless Steel
• 14" Long Ripple Style
• 240 Volts AC
• 5500 Watts
• Ultra Low Watt Density
• Integrated L6-30P Twist Lock Plug
• Integrated 1.5" Tri-Clamp Flange
• Epoxy filled making it waterproof

120 VOLT 1650 WATT FOLDBACK HEATING ELEMENT WITH INTEGRATED L6-30P PLUG

This product is manufactured especially and exclusively for Brew-Boss!

It features an integrated 1.5" Tri-Clamp ferrule as well as an integrated L6-30P twist lock plug! Never has it been so easy to convert to electric brewing. No longer do you have to figure out how to enclose your heater element to make it safe. Any L6-30R twist lock receptacle will connect to this element or use the Brew-Boss Heater Cable for a perfect fit.

This heater requires a 1.5" Tri-Clamp flange on your kettle (all Brew-Boss kettles have this flange welded on). If you are converting to electric or have another brand of kettle, you can add a Tri-Clamp flange by having one welded on locally or by using our Weldless 1.5 Inch Tri-Clamp Bulkhead Adapter.

The element is constructed of shiny 304 stainless steel and will look like new for years. it is an ULWD (Ultra Low Watt Density) element, so no worries about scorching your wort.

The element itself is 9 inches long and the ferrule is a 1.5" Tri-Clamp. Please order the clamp and gasket separately as they are not included with this item.

This listing is for the heater element only.

• 304 Stainless Steel
• 9" Long Foldback Style
• 120 Volts AC
• 1650 Watts
• Ultra Low Watt Density
• Integrated L6-30P Twist Lock Plug
• Integrated 1.5" Tri-Clamp Flange

120 VOLT 2250 WATT FOLDBACK HEATING ELEMENT WITH INTEGRATED L6-30P PLUG

This product is manufactured especially and exclusively for Brew-Boss! It is our highest wattage 120 volt element.

It features an integrated 1.5" Tri-Clamp ferrule as well as an integrated L6-30P twist lock plug! Never has it been so easy to convert to electric brewing. No longer do you have to figure out how to enclose your heater element to make it safe. Any L6-30R twist lock receptacle will connect to this element or use the Brew-Boss Heater Cable for a perfect fit. This element requires a 20 amp 120 volt AC circuit to operate. Most residential outlets are 15 amp circuits. Make certain that you have a 20 amp circuit if you plan to use this heater.

This heater requires a 1.5" Tri-Clamp flange on your kettle (all Brew-Boss kettles have this flange welded on). If you are converting to electric or have another brand of kettle, you can add a Tri-Clamp flange by having one welded on locally or by using our Weldless 1.5 Inch Tri-Clamp Bulkhead Adapter.

The element is constructed of shiny 304 stainless steel and will look like new for years. it is an ULWD (Ultra Low Watt Density) element, so no worries about scorching your wort.

The element itself is 9 inches long and the ferrule is a 1.5" Tri-Clamp. Please order the clamp and gasket separately as they are not included with this item.

• 304 Stainless Steel
• 9" Long Foldback Style
• 120 Volts AC
• 2250 Watts
• Ultra Low Watt Density
• Integrated L6-30P Twist Lock Plug
• Integrated 1.5" Tri-Clamp Flange

• 
  
• 

Your Beer, Your Way!!!

www.brew-boss.com

Condenser-Boss Boil Kettle Steam Condenser Demonstration

Winter is coming, keep your windows from steaming up with the Condenser Boss! Commercial breweries don't use exhaust hoods, instead they have elaborate & expensive steam condensing systems. Ours is an economical home brewer option!

Do you brew indoors and struggle with how to get rid of all the steam created during the brewing process, especially during the boil part of the brew process? Historically, home brewers installed electric fan exhaust hoods above their brew kettles and evacuated the steam to the outdoors. The problem with exhaust hoods is that all your conditioned air (heated or air conditioned) inside your home or brewery, is evacuated the outside while you are brewing. This means that your furnace/air conditioner has to work overtime to heat/cool the indoor air you air to keep up with what you are exhausting the outside! Over a 2 hour brew session, that represents a real cost as well as unnecessary wear and tear on your heating/cooling system.

Introducing the Condenser-Boss. This really cool device mounts directly to the Deluxe Accessory port on your Brew-Boss kettle (or most other boil kettles). We've tried/tested/researched several designs, using our concepts, as well as information found on public homebrewing forums, to finally settle on this design. This is the best design we have found!

Get yours today!!

https://www.brew-boss.com/Condenser-Boss-Boil-Kettle-Condenser-p/cb-bb-apmount.htm