ONLY $40 / 120 Volt 1650 Watt Stainless Steel Foldback Heating Element with integrated L6-30P Plug

ONLY $40 / 120 Volt 1650 Watt Stainless Steel Foldback Heating Element with integrated L6-30P Plug

NOW ONLY $40

120 VOLT 1650 WATT FOLDBACK HEATING ELEMENT WITH INTEGRATED L6-30P PLUG This product is manufactured especially and exclusively for Brew-Boss! It features an integrated 1.5" Tri-Clamp ferrule as well as an integrated L6-30P twist lock plug! Never has it been so easy to convert to electric brewing. No longer do you have to figure out how to enclose your heater element to make it safe. Any L6-30R twist lock receptacle will connect to this element or use the Brew-Boss Heater Cable for a perfect fit. This heater requires a 1.5" Tri-Clamp flange on your kettle (all Brew-Boss kettles have this flange welded on). If you are converting to electric or have another brand of kettle, you can add a Tri-Clamp flange by having one welded on locally or by using our Weldless 1.5 Inch Tri-Clamp Bulkhead Adapter. The element is constructed of shiny 304 stainless steel and will look like new for years. it is an ULWD (Ultra Low Watt Density) element, so no worries about scorching your wort. The element itself is 9 inches long and the ferrule is a 1.5" Tri-Clamp. Please order the clamp and gasket separately as they are not included with this item. This listing is for the heater element only. 304 Stainless Steel 9" Long Foldback Style 120 Volts AC 1650 Watts Ultra Low Watt Density Integrated L6-30P Twist Lock Plug Integrated 1.5" Tri-Clamp Flange

https://www.brew-boss.com/120-Volt-1650-Watt-Foldback-Heating-Element-p/htr-1650-foldback-l6-30p.htm

www.brew-boss.com

#120V1650WHeatingElement,#ElectricHeatingElement, #BrewBoss, #Homebrewing, #FoldbackHeatingElement

Now Only $40 / 120 Volt 2250 Watt Stainless Steel Foldback Heating Element with integrated L6-30P Plug

120 Volt 2250 Watt Stainless Steel Foldback Heating Element with integrated L6-30P Plug

NOW ONLY $40

120 VOLT 2250 WATT FOLDBACK HEATING ELEMENT WITH INTEGRATED L6-30P PLUG This product is manufactured especially and exclusively for Brew-Boss! It is our highest wattage 120 volt element. It features an integrated 1.5" Tri-Clamp ferrule as well as an integrated L6-30P twist lock plug! Never has it been so easy to convert to electric brewing. No longer do you have to figure out how to enclose your heater element to make it safe. Any L6-30R twist lock receptacle will connect to this element or use the Brew-Boss Heater Cable for a perfect fit. This element requires a 20 amp 120 volt AC circuit to operate. Most residential outlets are 15 amp circuits. Make certain that you have a 20 amp circuit if you plan to use this heater. This heater requires a 1.5" Tri-Clamp flange on your kettle (all Brew-Boss kettles have this flange welded on). If you are converting to electric or have another brand of kettle, you can add a Tri-Clamp flange by having one welded on locally or by using our Weldless 1.5 Inch Tri-Clamp Bulkhead Adapter. The element is constructed of shiny 304 stainless steel and will look like new for years. it is an ULWD (Ultra Low Watt Density) element, so no worries about scorching your wort. The element itself is 9 inches long and the ferrule is a 1.5" Tri-Clamp. Please order the clamp and gasket separately as they are not included with this item. This listing is for the heater element only. 304 Stainless Steel 9" Long Foldback Style 120 Volts AC 2250 Watts Ultra Low Watt Density Integrated L6-30P Twist Lock Plug Integrated 1.5" Tri-Clamp Flange

https://www.brew-boss.com/120-Volt-2250-Watt-Foldback-Heating-Element-p/htr-2250-foldback-l6-30p.htm

www.brew-boss.com

#SS2250, #ssheatingelement, #electricheatingelement, #homebrewing, #brewboss

Now Only $50 - 240 Volt 5500 Watt Stainless Steel Ripple Heating Element with integrated L6-30P Plug

Now Only $50 - 240 Volt 5500 Watt Stainless Steel Ripple Heating Element with integrated L6-30P Plug

Best Priced Heater Element - $50 Each

240 VOLT 5500 WATT RIPPLE HEATING ELEMENT WITH INTEGRATED L6-30P PLUG AND TRICLAMP MOUNT This product was designed by Brew-Boss and is manufactured exclusively for Brew-Boss! Beware of cheap copies with rubber band covers over the high voltage terminals and corrosive parts. They are not safe and are poorly constructed. The Brew-Boss heater is 100% potted with epoxy and is waterproof. No worries when cleaning about getting water inside the element. It features an integrated 1.5" Tri-Clamp ferrule as well as an integrated L6-30P twist lock plug! Never has it been so easy to convert to electric brewing. No longer do you have to figure out how to enclose your heater element to make it safe. Any L6-30R twist lock receptacle will connect to this element or use the Brew-Boss Heater Cable for a perfect fit. This heater requires a 1.5" Tri-Clamp flange on your kettle (all Brew-Boss kettles have this flange welded on). If you are converting to electric or have another brand of kettle, you can add a Tri-Clamp flange by having one welded on locally or by using our Weldless 1.5 Inch Tri-Clamp Bulkhead Adapter. The element is constructed of shiny 304 stainless steel and will look like new for years. it is an ULWD (Ultra Low Watt Density) element, so no worries about scorching your wort. The element itself is 14 inches long and the ferrule is a 1.5" Tri-Clamp. Please order the clamp and gasket separately as they are not included with this item. This listing is for the heater element only. Pictures of the element with the mating Brew-Boss Heater cable are shown only to show how the components fit together. 304 Stainless Steel 14" Long Ripple Style 240 Volts AC 5500 Watts Ultra Low Watt Density Integrated L6-30P Twist Lock Plug Integrated 1.5" Tri-Clamp Flange Epoxy filled making it waterproof

www.brew-boss.com

#electricheatingelement, #sselement, #homebrewing, #240V, #ripple, #heatingelement

https://www.brew-boss.com/product-p/accport-dlx.htm

DELUXE CAMLOCK ACCESSORY PORT Convert your kettle to use the Brew-Boss Sparge/Sprayer Wands, COFI infusion filters, and/or Swirl-Boss whirlpool device. This port has a Camlock nipple on the inside and outside of the kettle. Simply drill a 7/8" diameter hole near the top edge of your kettle. Includes two Camlock nipples, high temperature gasket, and special thin stainless steel washer.

www.brew-boss.com


#deluxecamlock #accessoryport #homebrewequipment, #ssaccessories #beer #kettleparts #mountaccessoriestobrewkettle #brewboss

Remove Steam While Brewing - Condenser-Boss Steam Condenser

https://www.brew-boss.com/Condenser-Boss-Boil-Kettle-Condenser-p/cb-bb-apmount.htm

CONDENSER-BOSS - STEAM CONDENSER

Do you brew indoors and struggle with how to get rid of all the steam created during the brewing process, especially during the boil part of the brew process? Historically, home brewers installed electric fan exhaust hoods above their brew kettles and evacuated the steam to the outdoors. In fact, you've probably seen that method used in some of our demonstration videos. The problem with exhaust hoods is that all your conditioned air (heated or air conditioned) inside your home or brewery, is evacuated the outside while you are brewing. This means that your furnace/air conditioner has to work overtime to heat/cool the indoor air you air to keep up with what you are exhausting the outside! Over a 2 hour brew session, that represents a real cost as well as unnecessary wear and tear on your heating/cooling system.

Commercial breweries don't use exhaust hoods, instead they have elaborate and expensive steam condensing systems attached to their boil kettles to condense steam back down to water. We've been working over a year testing various designs for a smaller simpler condenser that we could offer for our homebrew and small brewery customers that would attach directly to our Brew-Boss and Brew-Boss Pro kettles without modification.

Introducing the Condenser-Boss. This really cool device mounts directly to the Deluxe Accessory port on your Brew-Boss kettle (or most other boil kettles). We've tried/tested/researched several designs, using our concepts, as well as information found on public homebrewing forums, to finally settle on this design.




https://www.brew-boss.com/Condenser-Boss-Boil-Kettle-Condenser-p/cb-bb-apmount.htm

The image above shows how simple this device is. It is constructed from off the shelf parts! Basically, cold water is mixed directly with steam to condense the steam inside a Triclamp "T". The device is clamped onto the accessory port on the kettle. A cold water supply is connected to the device. This cold water supply can be tap water or could be water that you recirculate through a chiller or large tank using a pump that delivers at least 20psi. The device uses about 9-15 gallons of water per hour, depending on the temperature of the water and the power input to the kettle. A flow control valve is included that allows you to regulate the flow to the lowest flow you can that eliminates any steam from exiting the device. Note the image shows a camlock fitting for cold water supply connection. The device you will receive will have a female garden hose connenction.

When the steam condenses inside the device, the steam contracts and actually creates a vacuum inside the kettle, sucking the steam into the device. This assures that all the steam is evacuated and DMS is expelled. The result is a steady stream of warm water discharging at the bottom of the device. You can dicharge this via a hose (not included) to a drain, let it drain into a bucket as we show in the video, or create a closed loop where you cool the water and pump it back into the cold water inlet.

We also provide a gasket that you press onto the rim of the kettle that provides a steam-proof seal between the cover and the kettle, so that no steam can exit the kettle through the lid gaps. We found placing some weights on the cover help prevent leakage around the lid. Other providers do not supply this gasket!

After using this device for several brews, we've found that there was one huge, unexpected advantage, beyond eliminating the exhaust of our conditioned indoor air to the outside that we did not consider! We greatly reduced our electrical power used for the brew session!. Because the boil occurs with the cover on the kettle, the power requirement to maintain the boil was reduced to less than half! On our 20 gallon Brew-Boss system we use regularly, we typically had to boil at 63% power to maintain the proper boil. We-ve found that we can reduce that to 28% and maintain the same rolling boil! We feel sending 15 gallons of water down the drain, although not ecologically desirable, is way more than compensated by the power savings it provides during a 60-90 minute boil.

This item includes a female garden hose fitting that allows you to connect directly to the discharge end of a garden hose. It also includes the mini flow control valve that allows you to turn the device off right at the device and to regulate water flow to minimize flow.

The cost of this item may seem high, but is much less than the alternative of installing an exhaust hood, and that doesn't even consider the ongoing cost of heating/cooling your indoor air every time you brew!

NOTE: Unfortunately, this can't be used if you are using our Hops-Boss automated hops feeder.


APPLICATION NOTES: If you don't own a Brew-Boss kettle, and want to use this device, you have a few options to mount this device to your kettle.

Option 1: Purchase our Deluxe Accessory Port option for your kettle. Installation of the accessory port requires drilling a 7/8" diameter hole near the top of your kettle. This is the easiest way to add to third party kettles.

Option 2: If you would prefer to use a 1.5" Tri-Clamp flange on your kettle, select this option and we will not send the CamLock type connectors with the unit. It will simply ship with a 1.5" Tri-Clamp flange. With this option, we will also send you our Weldless 1.5 inch bulkhead triclamp flange adapter that you install on your kettle. This requires drilling a 41mm hole in your kettle. You will also need a Tri-Clamp gasket and clamp (not included).

Option 3: If you already have a 1.5" Tri-Clamp flange on your kettle, select this option and we will not send the CamLock type connectors with the unit or a Tri-Clamp bulkhead flange. It will simply ship with a 1.5" Tri-Clamp flange that you connect to your Tri-Clamp flange with a gasket and clamp (not included).

https://www.brew-boss.com/Condenser-Boss-Boil-Kettle-Condenser-p/cb-bb-apmount.htm

www.brew-boss.com

BREW-BOSS COFI MASH INFUSION FILTER FOR 15 GALLON KETTLE

BREW-BOSS COFI MASH INFUSION FILTER FOR 15 GALLON KETTLE Center Out Forced Infusion The Brew-Boss #COFI filter is an exciting technology that optimizes the efficiency of Brew-In-A-Bag (#BIAB) type brewing. The filter is manufactured from 304 grade stainless steel mesh which holds the grain during the mash process, but allows water to flow through. The filter is 13 inches in diameter x 13.5 inches high. The support legs allow the filter to sit above the heating element and are 2-1/2 inches tall. This brings the total height of the unit to 16 inches. The 90 degree barbed elbow at the top adds another 1-1/2 inches, for a total overall height of this filter with the barbed fitting installed of 17.5 inches. Make certain your kettle is tall enough to contain this filter with the cover on. The filter can hold approximately 20 pounds of crushed grain. This amount depends on the crush and the grain. This item is provided for brewers to add to their existing (Brew-Boss or other Manufacturer) breweries and includes the following items: Mesh basket with 2.5" long feet to clear heating element. Mesh Cover with Stainless Steel Clamps and Handle Center Infusion Tube False Bottom with Threaded Infusion Tube Mount Stainless Elbow Fitting for Top of Infusion Tube Stainless Lift Ring Adapter Type C Camlock Female Fitting 12" Silicone Brewery Grade Tubing A central infusion tube, that is perforated with a series of flow-matched holes, extends all the way to the bottom of the filter. During the mash cycle, water is continuously pumped from the bottom of the kettle to the top of the filter, into the central infusion tube, where it is forced through the grain bed. Water passing through the grain bed flows out of the filter to the bottom of the kettle. This Center Out Forced Infusion (COFI) technology assures that all the grain is in constant contact with the mash water and that there are no dead spots. No stirring is required as the system is self agitating and efficiency is thereby optimized. The COFI filter is also very easy to clean, simply invert it in a sink and spray it with your sprayer! Because it is made of stainless steel, it will not rust and will last indefinitely. The central infusion tube is also connected to a false bottom. After mashing is completed, the elbow fitting at the top of the COFI filter is exchanged with a lifting ring. When removing the filter, the filter is lifted by the lift ring. This brings the false bottom towards the fixed cover, allowing the weight of the filter to squeeze the grain. This squeezing action extracts much of the trapped sweet wort from the grain. www.brew-boss.com

Brew-Boss Automated Homebrew System Brew Session: App & COFI Filter

Brew-Boss Automated Homebrew System Brew Session
Brew-Boss Brewing Session Highlights. Takes you through the entire process of brewing with the Brew-Boss electric homebrew system. The COFI mash infusion system was used for this batch.
www.brew-boss.com

#electrichomebrew, #brewboss, #makegreatbeer, #biab, #makegreatbeer

Br

Brew Boss: Beer Brewing App - Talks you through the process

Brew-Boss Automated Electric Homebrew System App walks user through brewing process with Verbal prompts. Even users that have never brewed before can make All-Grain beer successfully their very first batch.
www.brew-boss.com

#homebrewing, #brewboss, #electricbrewingrocks, #makegreatbeer, #bestbeerbrewingappever

Br