Monday, December 9, 2019

Low Price SS Heatling Elements - 5500 Watt, 2250 Watt, 1650 Watt

Low Price SS Heatling Elements - 5500 Watt, 2250 Watt, 1650 Watt

5500 Watt - W
as $75, NOW $50
https://www.brew-boss.com/ULWD-L6-30P-Stainless-Steel-Ripple-Heater-Element-p/htr-5500-ripple-l6-30p.htm














Beware of cheap copies with rubber band covers over the high voltage terminals and corrosive parts. They are not safe and are poorly constructed. The Brew-Boss heater is 100% potted with epoxy and is waterproof. No worries when cleaning about getting water inside the element.

It features an integrated 1.5" Tri-Clamp ferrule as well as an integrated L6-30P twist lock plug! Never has it been so easy to convert to electric brewing. No longer do you have to figure out how to enclose your heater element to make it safe. Any L6-30R twist lock receptacle will connect to this element or use the Brew-Boss Heater Cable for a perfect fit.

This heater requires a 1.5" Tri-Clamp flange on your kettle (all Brew-Boss kettles have this flange welded on). If you are converting to electric or have another brand of kettle, you can add a Tri-Clamp flange by having one welded on locally or by using our Weldless 1.5 Inch Tri-Clamp Bulkhead Adapter.

The element is constructed of shiny 304 stainless steel and will look like new for years. it is an ULWD (Ultra Low Watt Density) element, so no worries about scorching your wort.

The element itself is 14 inches long and the ferrule is a 1.5" Tri-Clamp. Please order the clamp and gasket separately as they are not included with this item.

This listing is for the heater element only. Pictures of the element with the mating Brew-Boss Heater cable are shown only to show how the components fit together.

  • 304 Stainless Steel
  • 14" Long Ripple Style
  • 240 Volts AC
  • 5500 Watts
  • Ultra Low Watt Density
  • Integrated L6-30P Twist Lock Plug
  • Integrated 1.5" Tri-Clamp Flange
  • Epoxy filled making it waterproof















It features an integrated 1.5" Tri-Clamp ferrule as well as an integrated L6-30P twist lock plug! Never has it been so easy to convert to electric brewing. No longer do you have to figure out how to enclose your heater element to make it safe. Any L6-30R twist lock receptacle will connect to this element or use the Brew-Boss Heater Cable for a perfect fit. This element requires a 20 amp 120 volt AC circuit to operate. Most residential outlets are 15 amp circuits. Make certain that you have a 20 amp circuit if you plan to use this heater.

This heater requires a 1.5" Tri-Clamp flange on your kettle (all Brew-Boss kettles have this flange welded on). If you are converting to electric or have another brand of kettle, you can add a Tri-Clamp flange by having one welded on locally or by using our Weldless 1.5 Inch Tri-Clamp Bulkhead Adapter.

The element is constructed of shiny 304 stainless steel and will look like new for years. it is an ULWD (Ultra Low Watt Density) element, so no worries about scorching your wort.

The element itself is 9 inches long and the ferrule is a 1.5" Tri-Clamp. Please order the clamp and gasket separately as they are not included with this item.

This listing is for the heater element only.
  • 304 Stainless Steel
  • 9" Long Foldback Style
  • 120 Volts AC
  • 2250 Watts
  • Ultra Low Watt Density
  • Integrated L6-30P Twist Lock Plug
  • Integrated 1.5" Tri-Clamp Flange




1650 Watt -  Was $65, NOW $40

https://www.brew-boss.com/120-Volt-1650-Watt-Foldback-Heating-Element-p/htr-1650-foldback-l6-30p.htm


It features an integrated 1.5" Tri-Clamp ferrule as well as an integrated L6-30P twist lock plug! Never has it been so easy to convert to electric brewing. No longer do you have to figure out how to enclose your heater element to make it safe. Any L6-30R twist lock receptacle will connect to this element or use the Brew-Boss Heater Cable for a perfect fit.

This heater requires a 1.5" Tri-Clamp flange on your kettle (all Brew-Boss kettles have this flange welded on). If you are converting to electric or have another brand of kettle, you can add a Tri-Clamp flange by having one welded on locally or by using our Weldless 1.5 Inch Tri-Clamp Bulkhead Adapter.

The element is constructed of shiny 304 stainless steel and will look like new for years. it is an ULWD (Ultra Low Watt Density) element, so no worries about scorching your wort.

The element itself is 9 inches long and the ferrule is a 1.5" Tri-Clamp. Please order the clamp and gasket separately as they are not included with this item.

This listing is for the heater element only.
  • 304 Stainless Steel
  • 9" Long Foldback Style
  • 120 Volts AC
  • 1650 Watts
  • Ultra Low Watt Density
  • Integrated L6-30P Twist Lock Plug
  • Integrated 1.5" Tri-Clamp Flange




#heatingelements, #brewboss, #homebrew

Monday, November 25, 2019

Brew Boss Black Friday Sale 2019!!

Brew Boss Black Friday Sale 2019!!



























10 GALLON BREW-BOSS KETTLE KIT

10 Gallon Brew-Boss Kettle with Welded Tri-Clamp ferrules for the heaters and valve. This kettle includes three Tri-Clamp ferrules for the valve and dual heater assemblies. Also includes Cover, DELUXE Accessory Port, and Direct Contact Weldless Temperature Probe Mount.

Dia 350mm X H 420mm (13.75 in x 16.5 in) This is an optimum 1.2:1 ratio kettle!














This product was designed by Brew-Boss and is manufactured exclusively for Brew-Boss!

Beware of cheap copies with rubber band covers over the high voltage terminals and corrosive parts. They are not safe and are poorly constructed. The Brew-Boss heater is 100% potted with epoxy and is waterproof. No worries when cleaning about getting water inside the element.

It features an integrated 1.5" Tri-Clamp ferrule as well as an integrated L6-30P twist lock plug! Never has it been so easy to convert to electric brewing. No longer do you have to figure out how to enclose your heater element to make it safe. Any L6-30R twist lock receptacle will connect to this element or use the Brew-Boss Heater Cable for a perfect fit.

This heater requires a 1.5" Tri-Clamp flange on your kettle (all Brew-Boss kettles have this flange welded on). If you are converting to electric or have another brand of kettle, you can add a Tri-Clamp flange by having one welded on locally or by using our Weldless 1.5 Inch Tri-Clamp Bulkhead Adapter.

The element is constructed of shiny 304 stainless steel and will look like new for years. it is an ULWD (Ultra Low Watt Density) element, so no worries about scorching your wort.

The element itself is 14 inches long and the ferrule is a 1.5" Tri-Clamp. Please order the clamp and gasket separately as they are not included with this item.

This listing is for the heater element only. Pictures of the element with the mating Brew-Boss Heater cable are shown only to show how the components fit together.

  • 304 Stainless Steel
  • 14" Long Ripple Style
  • 240 Volts AC
  • 5500 Watts
  • Ultra Low Watt Density
  • Integrated L6-30P Twist Lock Plug
  • Integrated 1.5" Tri-Clamp Flange
  • Epoxy filled making it waterproof












120 VOLT 1650 WATT FOLDBACK HEATING ELEMENT WITH INTEGRATED L6-30P PLUG

This product is manufactured especially and exclusively for Brew-Boss!

It features an integrated 1.5" Tri-Clamp ferrule as well as an integrated L6-30P twist lock plug! Never has it been so easy to convert to electric brewing. No longer do you have to figure out how to enclose your heater element to make it safe. Any L6-30R twist lock receptacle will connect to this element or use the Brew-Boss Heater Cable for a perfect fit.

This heater requires a 1.5" Tri-Clamp flange on your kettle (all Brew-Boss kettles have this flange welded on). If you are converting to electric or have another brand of kettle, you can add a Tri-Clamp flange by having one welded on locally or by using our Weldless 1.5 Inch Tri-Clamp Bulkhead Adapter.

The element is constructed of shiny 304 stainless steel and will look like new for years. it is an ULWD (Ultra Low Watt Density) element, so no worries about scorching your wort.

The element itself is 9 inches long and the ferrule is a 1.5" Tri-Clamp. Please order the clamp and gasket separately as they are not included with this item.

This listing is for the heater element only.

  • 304 Stainless Steel
  • 9" Long Foldback Style
  • 120 Volts AC
  • 1650 Watts
  • Ultra Low Watt Density
  • Integrated L6-30P Twist Lock Plug
  • Integrated 1.5" Tri-Clamp Flange


This product is manufactured especially and exclusively for Brew-Boss! It is our highest wattage 120 volt element.

It features an integrated 1.5" Tri-Clamp ferrule as well as an integrated L6-30P twist lock plug! Never has it been so easy to convert to electric brewing. No longer do you have to figure out how to enclose your heater element to make it safe. Any L6-30R twist lock receptacle will connect to this element or use the Brew-Boss Heater Cable for a perfect fit. This element requires a 20 amp 120 volt AC circuit to operate. Most residential outlets are 15 amp circuits. Make certain that you have a 20 amp circuit if you plan to use this heater.

This heater requires a 1.5" Tri-Clamp flange on your kettle (all Brew-Boss kettles have this flange welded on). If you are converting to electric or have another brand of kettle, you can add a Tri-Clamp flange by having one welded on locally or by using our Weldless 1.5 Inch Tri-Clamp Bulkhead Adapter.

The element is constructed of shiny 304 stainless steel and will look like new for years. it is an ULWD (Ultra Low Watt Density) element, so no worries about scorching your wort.

The element itself is 9 inches long and the ferrule is a 1.5" Tri-Clamp. Please order the clamp and gasket separately as they are not included with this item.

  • 304 Stainless Steel
  • 9" Long Foldback Style
  • 120 Volts AC
  • 2250 Watts
  • Ultra Low Watt Density
  • Integrated L6-30P Twist Lock Plug
  • Integrated 1.5" Tri-Clamp Flange




    Your Beer, Your Way!!!

    Thursday, October 3, 2019

    Condenser-Boss Boil Kettle Steam Condenser Demonstration




    Winter is coming, keep your windows from steaming up with the Condenser Boss! Commercial breweries don't use exhaust hoods, instead they have elaborate & expensive steam condensing systems. Ours is an economical home brewer option!

    Do you brew indoors and struggle with how to get rid of all the steam created during the brewing process, especially during the boil part of the brew process? Historically, home brewers installed electric fan exhaust hoods above their brew kettles and evacuated the steam to the outdoors. The problem with exhaust hoods is that all your conditioned air (heated or air conditioned) inside your home or brewery, is evacuated the outside while you are brewing. This means that your furnace/air conditioner has to work overtime to heat/cool the indoor air you air to keep up with what you are exhausting the outside! Over a 2 hour brew session, that represents a real cost as well as unnecessary wear and tear on your heating/cooling system.

    Introducing the Condenser-Boss. This really cool device mounts directly to the Deluxe Accessory port on your Brew-Boss kettle (or most other boil kettles). We've tried/tested/researched several designs, using our concepts, as well as information found on public homebrewing forums, to finally settle on this design. This is the best design we have found!

    Get yours today!!

    https://www.brew-boss.com/Condenser-Boss-Boil-Kettle-Condenser-p/cb-bb-apmount.htm



    Thursday, August 29, 2019

    HOPS FILTER BASKET/SPIDER

    HOPS-BOSS HOPS FILTER BASKET/SPIDER 6X16"




    https://www.brew-boss.com/product-p/hb-filter0616.htm
    Hops filter basket. Keeps hops sediment out of your wort. Filter is constructed of 100% 304 Stainless Steel and is 6" dia x 16" tall with brackets that hang on the side of most brew kettles. It works as a stand-alone unit or with the Hops-Boss unit as well (see picture). This filter fits 15 and 20 gallon kettles only when used with the Hops-Boss as it is too tall for the 10 gallon kettle, although it can be set on the bottom of the 10 gallon kettle and used as a stand-alone filter.























    The basket is wrapped with 300 micron stainless steel wire mesh. 
    • 6" Diameter x16" Tall
    • 300 Micron
    • 100% 304 Stainless Steel
    • Easily cleaned




    Your Beer, Your Way!  Brew like a Boss!


    #hopsfilterspider, #hops, #brewboss, #homebrewingequipment, #biab


    Wednesday, August 7, 2019

    CONDENSER-BOSS - STAINLESS STEEL ACCESSORY PORT MOUNTED STEAM CONDENSER




















    CONDENSER-BOSS - STAINLESS STEEL ACCESSORY PORT MOUNTED STEAM CONDENSER

    Do you brew indoors and struggle with how to get rid of all the steam created during the brewing process, especially during the boil part of the brew process? Historically, home brewers installed electric fan exhaust hoods above their brew kettles and evacuated the steam to the outdoors. In fact, you've probably seen that method used in some of our demonstration videos. The problem with exhaust hoods is that all your conditioned air (heated or air conditioned) inside your home or brewery, is evacuated the outside while you are brewing. This means that your furnace/air conditioner has to work overtime to heat/cool the indoor air you air to keep up with what you are exhausting the outside! Over a 2 hour brew session, that represents a real cost as well as unnecessary wear and tear on your heating/cooling system.

    Commercial breweries don't use exhaust hoods, instead they have elaborate and expensive steam condensing systems attached to their boil kettles to condense steam back down to water. We've been working over a year testing various designs for a smaller simpler condenser that we could offer for our homebrew and small brewery customers that would attach directly to our Brew-Boss and Brew-Boss Pro kettles without modification.

    Introducing the Condenser-Boss. This really cool device mounts directly to the Deluxe Accessory port on your Brew-Boss kettle (or most other boil kettles). We've tried/tested/researched several designs, using our concepts, as well as information found on public homebrewing forums, to finally settle on this design. 


























    The image above shows how simple this device is. It is constructed from off the shelf parts! Basically, cold water is mixed directly with steam to condense the steam inside a Triclamp "T". The device is clamped onto the accessory port on the kettle. A cold water supply is connected to the device. This cold water supply can be tap water or could be water that you recirculate through a chiller or large tank using a pump that delivers at least 20psi. The device uses about 9-15 gallons of water per hour, depending on the temperature of the water and the power input to the kettle. A flow control valve is included that allows you to regulate the flow to the lowest flow you can that eliminates any steam from exiting the device. Note the image shows a camlock fitting for cold water supply connection. The device you will receive will have a female garden hose connenction.

    When the steam condenses inside the device, the steam contracts and actually creates a vacuum inside the kettle, sucking the steam into the device. This assures that all the steam is evacuated and DMS is expelled. The result is a steady stream of warm water discharging at the bottom of the device. You can discharge this via a hose (not included) to a drain, let it drain into a bucket as we show in the video, or create a closed loop where you cool the water and pump it back into the cold water inlet.

    We also provide a gasket that you press onto the rim of the kettle that provides a steam-proof seal between the cover and the kettle, so that no steam can exit the kettle through the lid gaps. We found placing some weights on the cover help prevent leakage around the lid.

    After using this device for several brews, we've found that there was one huge, unexpected advantage, beyond eliminating the exhaust of our conditioned indoor air to the outside that we did not consider! We greatly reduced our electrical power used for the brew session!. Because the boil occurs with the cover on the kettle, the power requirement to maintain the boil was reduced to less than half! On our 20 gallon Brew-Boss system we use regularly, we typically had to boil at 63% power to maintain the proper boil. We-ve found that we can reduce that to 28% and maintain the same rolling boil! We feel sending 15 gallons of water down the drain, although not ecologically desirable, is way more than compensated by the power savings it provides during a 60-90 minute boil.

    Condenser Boss includes a female garden hose fitting that allows you to connect directly to the discharge end of a garden hose. It also includes the mini flow control valve that allows you to turn the device off right at the device and to regulate water flow to minimize flow.

    The cost of this item may seem high, but is much less than the alternative of installing an exhaust hood, and that doesn't even consider the ongoing cost of heating/cooling your indoor air every time you brew!


    NOTE: If you don't own a Brew-Boss kettle, and want to use this device, you need to also purchase our Deluxe Accessory Port for your kettle. Installation of the accessory port requires drilling a 7/8" diameter hole near the top of your kettle.



    YOUR BEER, YOUR WAY!
    Brew Like a Boss!



    #steamcondenser, #condenserboss, #brewboss, #homebrewequipment, #getridofsteam, #biab, 

    Tuesday, August 6, 2019

    Brew Boss: DELUXE CAMLOCK ACCESSORY PORT












    DELUXE CAMLOCK ACCESSORY PORT

    Convert your kettle to use the Brew-Boss Sparge/Sprayer Wands, COFI infusion filters, and/or Swirl-Boss whirlpool device. This port has a Camlock nipple on the inside and outside of the kettle. Simply drill a 7/8" diameter hole near the top edge of your kettle. Includes two Camlock nipples, high temperature gasket, and special thin stainless steel washer.







    Your Beer, Your Way!  Brew like a Boss!


    #camlockaccessoryport #camlock #brewboss #homebrewequipment #brewkettle


    Friday, August 2, 2019

    240 Volt 5500 Watt Stainless Steel Ripple Heating Element with integrated L6-30P Plug




    This product was designed by Brew-Boss and is manufactured exclusively for Brew-Boss! 

    Beware of cheap copies with rubber band covers over the high voltage terminals and corrosive parts. They are not safe and are poorly constructed. The Brew-Boss heater is 100% potted with epoxy and is waterproof. No worries when cleaning about getting water inside the element.

    It features an integrated 1.5" Tri-Clamp ferrule as well as an integrated L6-30P twist lock plug! Never has it been so easy to convert to electric brewing. No longer do you have to figure out how to enclose your heater element to make it safe. Any L6-30R twist lock receptacle will connect to this element or use the Brew-Boss Heater Cable for a perfect fit.

    This heater requires a 1.5" Tri-Clamp flange on your kettle (all Brew-Boss kettles have this flange welded on). If you are converting to electric or have another brand of kettle, you can add a Tri-Clamp flange by having one welded on locally or by using our Weldless 1.5 Inch Tri-Clamp Bulkhead Adapter

    The element is constructed of shiny 304 stainless steel and will look like new for years. it is an ULWD (Ultra Low Watt Density) element, so no worries about scorching your wort.

    The element itself is 14 inches long and the ferrule is a 1.5" Tri-Clamp. Please order the clamp and gasket separately as they are not included with this item. 

    This listing is for the heater element only. Pictures of the element with the mating Brew-Boss Heater cable are shown only to show how the components fit together. 

    • 304 Stainless Steel
    • 14" Long Ripple Style
    • 240 Volts AC
    • 5500 Watts
    • Ultra Low Watt Density
    • Integrated L6-30P Twist Lock Plug
    • Integrated 1.5" Tri-Clamp Flange
    • Epoxy filled making it waterproof


    Click to Buy:



    Your Beer, Your Way!  Brew like a Boss!


    #ssheatingelement, #homebrewequipment, # brewboss, #heatingelement, #beer

    When and How to Measure and Adjust Mash pH for Beer Brewing by BeerSmith

    http://beersmith.com/blog/2017/10/18/when-and-how-to-measure-and-adjust-mash-ph-for-beer-brewing/

    When and How to Measure and Adjust Mash pH for Beer Brewing


    by BRAD SMITH

    At a recent homebrew club meeting, one of the members asked me a brilliant question – when and how should you adjust your mash pH when all grain beer brewing? This is a devilishly complex question as you want to adjust your mash pH quickly if brewing with modern malts.

    The Mash pH Conundrum

    I and others have written extensively on the importance of controlling your mash pHand maintaining it in the range of 5.2-5.6 during the sugar conversion step. A proper mash pH contributes to better flavor, complete conversion, and improved long term stability.

    You can use additives like lactic acid and phosphoric acid to quickly adjust your mash pH, and I wrote an article recently on the purchase and care of a pH meter. So one might assume you can just use your pH meter to measure the mash pH after dough-in of the grains and then adjust it using lactic acid from the homebrew shop — right?

    The problem is that most modern malts are very highly modified, which means they have a lot more enzymes (diastatic power) than is really needed to convert the sugars in your crushed grains into fermentable forms. Time is also working against us since it takes easily 10-15 minutes to dough in and stabilize the mash pH so it can be measured. Modern highly modified pale malts can in many cases convert the sugars within 20-30 minutes.

    It could take 10-15 minutes to dough in, and another 5-10 minutes to get the mash sample down to room temperature to take a proper measurement then calculate and add the right amount of lactic acid. Which means it is possible for the majority of your conversion step to be complete before you’ve measured and adjusted your pH!

    Managing Mash pH Properly

    Fortunately you can estimate both your predicted mash pH and the predicted acid adjustment needed using software. Here’s a detailed article on how to do it in BeerSmith. The only problem here is that the pH estimate is exactly that – an estimate!

    So the compromise I’ve settled on is to use BeerSmith to estimate my mash pH, then use that estimated value to determine the amount of lactic acid to use. Then what I do is add about 80% of that acid up front before I mash in. This usually gets my mash pH within the acceptable 5.2-5.6 range, and then I will take a measurement with my pH meter after I dough in and make any fine adjustments needed with some additional acid based on that measurement.

    The advantage of this technique is that by adding most of the acid up front, I’m assuring that the mash pH starts in the acceptable range. However, by also measuring and making a final pH adjustment I’m assuring that the pH is stable if the mash conversion takes longer but most importantly assuring the correct pH to support the long term stability of the beer.

    This is the best compromise between treating your mash based only on an estimate, and treating your mash pH based on an actual pH measurement.




    Your Beer, Your Way!  Brew like a Boss!


    #homebrew #measureph #beerbrewing #brewboss #hops #mash, 

    Monday, July 29, 2019

    240 Volt Brew-Boss Electric Brewery Controller Version 3

    https://www.brew-boss.com/Brew-Boss-240-Volt-Electric-Brewery-Controller-V3-p/bb240-diy-v3.htm



    240 Volt Brew-Boss Electric Brewery Controller Version 3

    Brew-Boss V3 electric brewing controller. This option is for those that already have a gas based brewing system and want to convert to the benefits of electric brewing or want to create their own electric brewery.

    This newly designed controller replaces our previous controller. It includes the following features:

    ● Molded L6-30P Twist Lock Plug with 15’ power cord.
    ● L6-30R Receptacle for the heater. This allows longer length cables to be used for connecting to the heater.
    ● New 20 character x 4 line Backlit LCD provides more information on the Controller. Especially nice for fermentation mode.
    ● Integrated wifi radio for connection to the Brew-Boss Android tablet app.
    ● Front mounted outlet for the pump (controlled by app) and “always on” outlet for the tablet charger.
    ● Front mounted temperature probe jack.
    ● Can be wall mounted or simply placed on a table or work surface.
    ● Universal voltage (208-240VAC) works in most countries.
    ● Industrial lockable rotary master switch is front mounted for easier access.
    ● Custom designed DUAL SSR for reliable heater and pump operation.

    The new V3 controller includes the following improvements over previous versions:

    New 32-bit processor is faster and more powerful than previous versions
    Robust WiFi integrated into the controller with easier configuration for home and office networks
    Automatic firmware updates over the web when controller connected to internet
    Added a rotary input switch that allows users to:
    • - Manually control brewing functions right on the controller
    • - Control fermentation
    • - Brew without the need for the companion Android App
    • - Set temperature setpoints for the controller to hold automatically
    • - Set a countdown timer
    • - Control and Configure the Hops-Boss and Accu-Fill devices
    • - Set brewing parameters
    New accessory port that allows the Hops-Boss and Accu-Fill devices to be plugged in and automatically recognized by the controller.
    Added menu functions that allow setting of operational parameters

    The controller is universal for all countries that have 208-240 volt power. No separate 120 volt input is required for the USA when used with our new universal voltage DC pumps. (Note, this controller only works with 208-240 volt pumps!). The new controller also has a dedicated always on 240 volt receptacle for powering/charging the tablet! If you want to use the controller with a 120 volt pump, you will need to purchase an appropriately sized transformer device to step the voltage down for your pump. We recommend this unit or similar.

    This controller requires a 208-240 Volt 30 Amp circuit with a GFI breaker installed to operate. A digital temperature probe is included with this controller. The controller is shipped with a L6-30R twist lock receptacle for a heater that mates to the Brew-Boss integrated elements. If you have a different heater, you can simply add a L6-30P plug to your heater. The L6-30R connector provided also matches the Blichmann Engineering Boil-Coil.

    https://www.brew-boss.com/Brew-Boss-240-Volt-Electric-Brewery-Controller-V3-p/bb240-diy-v3.htm



















    Your Beer, Your Way!  Brew Boss



    #electricbrewcontroller, #electricbrewing, #homebrewing, #brewboss, #controller, #brewcontroller



    Tuesday, July 16, 2019

    Low Carb - Keto Quick Chocolate Cakes!



    Keto Quick Chocolate Cakes

    Low Carb Chocolate Cake (Pack of 9 Cakes)


    Click Here to Order Now!

    This decadent chocolate cake with only 2 net carbs will satisfy your sweet cravings. Top it with whipped cream for a truly exquisite experience.


    This cake is ideal for mid day or late night snacks, as a quick breakfast treat, or as a snack at work. The cake is supplied in a single serving microwavable container. Simply peel the top seal off the cup, add 3 tablespoons water and mix with a fork or spoon. Microwave for 40 seconds (may require more or less time depending on your microwave). Top with whipped cream or butter if desired and enjoy right out of the cup.







    Price includes free priority mail shipping in the lower 48 US states.Click Here to Order Now!













    #keto, #quickketo, #ketoquick, #ketocake, #ketochocolatecake, #ketodessert  #goodchocolatecake, #lowcarbchocolatecake

    Sunday, July 14, 2019

    Quarter Party Tabletop Coinhole Game

    CLICK HERE TO PURCHASE:  https://www.brew-boss.com/Quarter-Party-Tabletop-Cornhole-Game-p/quarterpartygame.htm

    Quarter Party Tabletop Cornhole Game







    This is the most awesome party game for groups of people like parents and players of traveling sports teams.

    We find that this game is the first thing we pack when packing for our team overnights. Our daughter is a club volleyball player and we travel nationally for tournaments and end up in hotels with the other player's parents with nothing to do. Each year she may switch teams so we end up needing to get acquainted with an entirely new group of players and parents. This game is a real ice breaker. Everyone loves it and request we bring it to every tournament. We tried the similar wooden games on the market and, because they don't hold up well over time, we decided to invest in the vacuum forming tooling to make our own improved version. All our parents asked us for one, so we decided to make them available to everyone.

    Although similar in looks to a traditional cornhole game, we've changed the rules to make it much more lively and action packed. It is played on a table top with players seated around the perimeter of the table. It makes an excellent drinking game as well as a betting game. It can be played by as few as 2 players and up to as many as 20+ players.

    Each player has their own coin (US quarter is best, but nickles and dimes work as well). If you are playing for money prizes, every player places the appropriate anti into a kitty cup. We usually have each player put a quarter in the cup. The winner of the round will ultimately receive the entire contents of the kitty cup.

    The game is started by selecting two starting players on opposite sides of the table (same number of people separating them on both sides from one another). One of the starting players is usually the winner of the last round. This is such a fun game that you will find you play many rounds! Each of the starting players is presented with one of the Quarter Party game boards.

    Someone yells out "Quarter Party" and the two starting players with the game boards begin trying to get their coin into the hole on the game board. The player plays by bouncing the coin off the table so that it lands ideally in the hole on the game board. The players can only use their own quarter to play and must retrieve it wherever it lands after each unsuccessful attempt. A side twist if it is a drinking game as well is to require that the player drink from their beverage before continuing play! Once a player is successful in getting their coin into the hole on the game board, he/she passes the game board to the player on their left (clockwise around table).

    The goal is to catch the other game board, so getting your coin into the hole as quickly as possible keeps you in the game. If a player makes the shot and the player on their left is still trying, he/she places the game board on top of the player's game board that is still trying. The player that got caught is now out of the game.

    Play is resumed by starting again with the game boards distributed to players on opposite sides of the table with equal number of other players between them. The player that just took another player out is one of the starting players. If there are an odd number of remaining players, the player that just took another player out gets the advantage and will have fewer players to his/her left than the other player.

    Play continues until only two players are left and they battle it out head to head. The winner gets the contents of the kitty cup!


    There are similar games on the market made of wood. Wood is heavy and the units take up space in your luggage. It also dents easily and becomes blemished and the varnish on some models becomes sticky from beverages consumed during play!. We fabricated this game out of strong textured plastic to give the best play dynamics. The plastic boards are molded and nest easily for packing and are very light weight.

    We've found that 2 boards are good for up to 10 players. If you will have more players than that, you may want to introduce a third and even a fourth board into the game. Remove game boards as appropriate as the number of remaining players is reduced. This item includes 2 playing boards.

    Quarter Party Features:
    • Strong & Lightweight - Fits in luggage easily
    • Great for Kids & Adults
    • Great travel size game
    • Fun
    • Excellent for parties
    • Vacuum Formed Durable ABS plastic
    • Nesting design packs easily
    • Textured surface provides best surface for coins to slide into hole and resists scratching
    • Easily cleaned
    • Approximate size: 5" x 7" x 2"
    • 2 Playing boards included



    #coinholegame #quarterparty #minicornhole #minibagsgame #summerpartygame #partygame #quartersdrinkinggame #familygame #gameforlargeamountofpeople